11 Mistakes Every New Homebrewer Makes
I was inspired by coaching one of my coworkers through his first batch of homebrew (an English bitter) to write up a list of the mistakes that many new homebrewers make. Several of these are things I did on early batches, while others I have tasted at homebrew at club meetings. Many of these issues stem from poor kit instructions, bad homebrew shop advice, and common sense that just doesn’t work out.
"Short and helpful." 5 stars by Duane
NoteStreams are readable online but they’re even better in the free App!
The NoteStream™ app is for learning about things that interest you: from music to history, to classic literature or cocktails. NoteStreams are truly easy to read on your smartphone—so you can learn more about the world around you and start a fresh conversation.
For a list of all authors on NoteStream, click here.
Read the NoteStream below, or download the app and read it on the go!
Mistakes Homebrewers Make
I was inspired by coaching one of my coworkers through his first batch of homebrew (an English bitter) to write up a list of the mistakes that many new homebrewers make.
Several of these are things I did on early batches, while others I have tasted at homebrew at club meetings. Many of these issues stem from poor kit instructions, bad homebrew shop advice, and common sense that just doesn’t work out.
1. Using the sanitizer that comes with a beer kit.
This powdered sanitizer is slow and not especially effective. Instead get a no-rinse sanitizer like Star-San or Iodophor, which are faster and easier to use. Sanitize everything that touches your beer post-boil, and make sure it is carefully cleaned after each use (sanitizers are most effective on scrupulously-clean scratch-free surfaces). Keeping wild microbes out of your beer is the single most important step to brewing solid beer.
Fermenting Barley Wine
Image by Michael Tonsmeire
Starting With A Complex Recipe
2. Starting with a recipe that is strong or unusual.
Brewing a big complex beer is lots of fun, but play it safe on your first batch and brew something simple. High alcohol beers require more yeast and time. Interesting adjuncts add complexity to the recipe and process. These are things you don’t want to deal with on your first batch, so keep it easy.
Using Tap Water
3. Brewing with unfiltered, chlorine-containing tap water.
If you are on a municipal water supply odds are that it contains either chlorine or chloramines. To remove them you can either charcoal filter or treat your water with metabisulfite, or alternatively use bottled water. One of the most common off-flavors I taste at homebrew club meetings is medicinal chlorophenol, which is formed by the combination of chlorine in the water or sanitizer and phenols from malt and yeast.
Squeezing The Grains
4. Squeezing the grain bag after steeping.
This releases tannins, which give the body a rough texture. Steep your grains in a small amount of water (no more than three quarts per pound) and then rinse them by either pouring hot water over the grain bag or dipping the grain bag into a second pot of hot water.
Edit: I've had a couple people dispute squeezing being an issue in the comments. I've tasted some tannin-y beer from new homebrewers, but maybe it was just from a high water to grain steeping ratio. I'll have to squeeze the grain bag into a glass and have a taste the next time I brew an extract beer.
5. Using liquid yeast.
"Pitchable" liquid yeast cultures barely have enough cells to ferment a standard gravity beer on the day they are packaged, and their cells die quickly from there. A high quality 11.5 g package of dried yeast starts with as much as twice the cells as a fresh package of yeast from either Wyeast or White Labs, and retains high cell viability for much longer.
While Fermentis, for example, claims a minimum of 6 billion cells per gram at packaging, the actual number tends to be much higher. Liquid yeast can produce great beers, but require a starter unless you are getting extremely fresh yeast and brewing a low-alcohol beer.
Image by Michael Tonsmeire
Not Enough Ventilation
6. Not aerating the wort adequately.
It takes several minutes of shaking for the chilled wort to absorb the ideal amount of oxygen to allow the yeast to complete a healthy growth phase. The healthier your yeast cells are the cleaner and quicker they will complete the fermentation.
Wait For The Right Temperature
7. Pitching when the side of the pot or fermentor feels “cool enough.”
Use a sanitized thermometer to check the actual temperature of the wort before you add the yeast. Pitching when the wort is above 100 F is rare, but will kill the yeast. Ideally the temperature should be at or below your target fermentation temperature to allow the temperature to rise as the yeast grows and ferments. You can pre-chill the sanitized water you use to top-off after the boil to help bring the temperature down.
8. Fermenting at too high of a temperature.
Take note of the ambient temperature of the room the beer is fermenting in, but realize that at the peak of fermentation the yeast can raise the temperature of the beer by as much as 7 F. Fermenting too warm can cause the yeast to produce higher alcohols and excessive fruity flavors. Letting the ambient temperature rise towards the high end of the yeast's range as fermentation slows helps to ensure a clean well attenuated beer, but for most strains is unnecessary. If you are unable to control the fermentation temperature, then choose a yeast strain that fits the conditions.
A Secondary Fermentor
9. Racking to secondary.
I know the instructions included in most kits call for transferring the beer from the primary fermentor to a secondary before bottling, but all this step accomplishes is introducing more risk of oxidation and wild yeast contamination. There is no risk of off flavors from autolysis (yeast death) at the homebrew scale in less than a month.
At a commercial level the pressure and heat exerted on the yeast can cause problems quickly, but those conditions do not exist in a carboy or bucket.
Keep it Simple
10. Relying on bubbles in the airlock to judge when fermentation is complete.
Wait until fermentation has appeared finished for a couple of days before pulling a sample of wort to test the final gravity. There is no rush to bottle, and doing so before the final gravity is reached results in extra carbonation. Once fermentation is complete and the beer tastes good, you can move the fermentor somewhere cool to encourage the yeast to settle out for clearer beer in the bottle.
Too Much Sugar
11. Adding the entire five ounce package of priming sugar.
In almost all cases this amount of sugar will over-carbonate the beer. Even for five gallons of beer this will produce too much carbonation for most styles and most brewers will end up with less than five gallons in the bottling bucket. Instead use a priming sugar calculator to tailor the weight of sugar you add to the actual volume of beer, the style of beer you are brewing, and the fermentation temperature.
Hopefully this list is able to help a few new homebrewers avoid some of the biggest pitfalls on their first batch.
If any of the more experienced brewers out there has any lessons learned that are not included on the list please post a comment. You should also pick up a good basic homebrewing book, like John Palmer’s How to Brew, especially if you want to learn more of the “why” behind some of my suggestions.
Selecting The Ingredients
There are many other things I would suggest as best practices, but they tend to be more style specific and are not worth worrying about on your first batch.
I also think fresh high quality ingredients are a big key to making good beer, but most people brewing their first batch are buying and using fresh malt, yeast, and hops.